Total :
0,0€
Replacement – Custom frame protection – Sublimistick Integral
7,0€ – 60,0€ TTC
Description
To order replacement patches, follow these steps:
1. Patch selection (first drop-down menu): Select the area of the frame you wish to replace. You have the following options:
– Top tube: patch for the top tube.
– Down tube: patch for the bottom tube.
– Entire front triangle: set of patches covering the entire front part of the frame.
– Entire rear triangle: a set of patches covering the entire rear of the frame.
– Small patch: for small areas such as the bottom bracket or sprocket set.
– Middle patch: for medium-sized areas such as chainstays, seatstays or seat tube.
2. Patch number selection (second drop-down menu) :
– If you selected “all front triangle” or “all rear triangle” in the first menu, you must re-select the same option (“all front triangle” or “all rear triangle”) in the second menu.
– If you have selected another option in the first menu (such as “top tube”, “down tube”, “small patch” or “middle patch”), then choose the patch number corresponding to the replacement zone (see kit manual).
3. Choice of finish (third drop-down menu):
Select the desired finish for the patch: matte or gloss.
Ordering multiple patches :
If you wish to order several patches (other than “all front triangle” or “all rear triangle” sets), you must add one item per patch.
For example, if you want to replace a shroud patch and a bottom bracket patch, add a “middle patch” item for the shroud and a “small patch” item for the bottom bracket to the basket.
4. Indicate your bike model: At the end of your order, when validating the basket, add a comment with the brand, model, size and year of your bike to ensure patch compatibility.
Additional information
Additional information
| Weight | 0,1 kg |
|---|---|
| Patch | DOWNTUBE, TOPTUBE, MIDDLE PATCH, SMALL PATCH, FRONT TRIANGLE, REAR TRIANGLE |
| Numéro Patch | FRONT TRIANGLE, REAR TRIANGLE, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29 |
| Finish | Glossy, Matte |
Installation
Installation
The installation of a Sublimistick Integral protection kit requires calm and thoroughness. If you are not sure of your skills, we invite you to contact your nearest Slicy dealer for a perfect set-up. Find our dealers HERE
Preparation :
– Make sure you are in a clean and warm, indoor space (17°C to 27°C).
– Clean and degrease your bike paying close attention to every little detail.
– Remove inconvenient components or old decals to facilitate the installation.
– Ensure the bike has been allowed to dry for some hours.
– Fill the spray bottle with our install shampoo. Add 0.5ml for 0.5L of warm water.
– Thoroughly wash your hands.
Installation :
– Identify Sublimistick sections using the bike diagram.
– Select pieces in number order (starting with No.1)
– Spray water to your fingers.
– Peel the section of Sublimistick off and spray water immediately on the sticky side.
– Spray water on the frame’s location.
– Apply the wet Sublimistick section to the frame. Center and line up the piece according to the diagram.
– Repositionining is possible if the Sublimistick section is still wet.
To move, peel back, add further water to the frame and Sublimistick section then re-apply in correct location.
– Use the Slicy squeegee to remove water and air. Start at the centre of the Sublimistick section and pull the water and air to the outside.
– Use the microfiber to collect any excess water.
– Wait few minutes and use your fingers to check if all edges are firmly pressed down.
– For a perfect finish, use the hair dryer to dry the Sublimistick sections. Do not overheat.
– Repeat these steps for each section of Sublimistick.
– Kits are designed with a 3mm gap between Sublimistick sections.
– Let your bike dry in a warm workspace for 24h.
– Do not ride or wash your bike for 24h.
Removal :
– Use a hair dryer to heat the adhesive.
– Peel back a corner and remove remove the section very slowly.
Disclaimers :
– Slicy is not responisble for any damage caused to your bike during installation or removal of the Sublimistick Integral Kit.
– If you have any problems or issues with your Sublimistick Integral Kit, please contact a member of our team at: contact@slicy-products.com.
Request a Tailored Protection Kit
Request a Tailored Protection Kit
Haven’t found the right kit for your bike? Don’t panic, we’ll take care of you!
Every week our team works hard to add new bikes to our kit catalogue. If we have not yet had the opportunity to create the right kit for your bike, we invite you to make your request by filling out the form below.
As you can imagine, we will not be able to develop all kits for all bikes. We will select those that will be useful for the maximum number of riders. New collections will be favoured as well as sizes M and L.
To develop a kit, our team needs to have the bike in their hands. Thank to our local Slicy dealers that allow us to have access to these bikes in order to develop the templates. It’s also possible to receive you in our workshop, accompanied by your bike, if you live near Annecy, France.
Lead time & Delivery
Lead time & Delivery
All our customized products are made to order which implies a longer delivery time.
How does it work?
Our team prepares the printing files every day and sends them to production every Thursday. Manufacturing starts on Thursday afternoon and the products are ready to be shipped the following Tuesday.
Delivery times are generally 5 to 12 business days.
